|
|
|
|
|
|
GATE Download Mechanical Engg Question Papers |
GATE Download Mechanical Engg Question Papers
Mechanical Engg papers 01 Questions And Answers No. Question
1 Stokes theorem connects
Options A) a line integral and a surface integral B) a surface integral and a volume integral
C) a line integral and a volume integral
D) gradient of a function and its surface integral
Your Answer ( Not Answered )
Correct Answer A
2 Match the following
Type of Mechanism Motion achieved
P. Scott — Russel mechanism 1. Intermittent motion
Q. Geneva mechanism 2. Quick return motion
R. Off-set slider-crank mechanism 3. Simple harmonic motion
S. Scotch Yoke mechanism 4. Straight line motion
Options A) P-2 Q-3 R-l S-4
B) P-3 Q-2 R-4 S-l
C) P-4 Q-l R-2 S-3
D) P-4 Q-3 R-l S-2
Your Answer ( Not Answered )
Correct Answer C
3 A solar collector receiving solar radiation at the rate of 0.6 k W/m 2 transforms it to the internal energy of a fluid at an overall efficiency of 50%. The fluid heated to 350 K is used to run a heat engine which rejects heat at 313 K. If the heat engine is to deliver 2.5 kW power, the minimum area of the solar collector required would be
Options A) 8.33m 2 B) 16.66m 2
C) 39.68m 2 D) 79.36m 2
Your Answer ( Not Answered )
Correct Answer D
4 When the temperature of a solid metal increases,
Options A) strength of the metal decreaes but ductility increases
B) both strength and ductility of the metal decrease
C) both strength and ductility of the metal increase D) strength of the metal increases but ductility decreases
Your Answer ( Not Answered )
Correct Answer A
5 A company produces two types of toys: P and Q. Production time of Q is twice that of P and the company has a maximum of 2000 time units per day. The supply of raw material is just sufficient to produce 1500 toys (of any type) per day. Toy type Q requires an electric switch which is available @ 600 pieces per day only. The company makes a profit of Rs. 3 and Rs. 5 on type P and Q respectively. For maximization of profits, the daily production quantities of P and Q toys should respectively be
Options A) 100, 500 B) 500, 1000
C) 800, 600 D) 1000, 1000
Your Answer ( Not Answered )
Correct Answer C
6 A spherical thermocouple junction of diameter 0.706 mm is to be used for the measurement of temperature of a gas stream. The convective heat transfer co-efficient on the bead surface is 400 W/m 2 K. Thermophysical properties of thermocouple material are k = 20 W/mK, C = 400 J/kg K and r = 8500 kg/m 3 . If the thermocouple initially tot 30°C is placed in a hot stream of 300°C, the time taken by the bead to reach 298°C, is
Options A) 2.35 s B) 4.9 s
C) 14.7 s D) 29.4 s
Your Answer ( Not Answered )
Correct Answer B
7 In a spring-mass system, the mass is 0.1 kg and the stiffness of the spring is 1 kN/m. By introducing a damper, the frequency of oscillation is found to be 90% of the original value. What is the damping coefficient of the damper?
Options A) 1.2 N.s/m B) 3.4 N.s/m
C) 8.7 N.s/m D) 12.0 N.s/m
Your Answer ( Not Answered )
Correct Answer C
8 In a machining operation, doubling the cutting speed reduces the tool life to 1
8
of the original value. The exponent n in Taylor
Options A) 1
8
B) 1
4
C) 1
3
D) 1
2
Your Answer ( Not Answered )
Correct Answer C
9 In a rolling process, sheet of 25 mm thickness is rolled to 20 mm thickness. Roll is of diameter 600 mm and it rotates at 100 rpm. The roll strip contact length will be
Options A) 5 mm B) 39 mm
C) 78mm D) 120mm
Your Answer ( Right Answer )
10 The values of a function f(x) are tabulated below
x f(x)
0 1
1 2
2 1
3 10
Using Newton , s forward difference formula, the cubic polynomial that can be fitted to the above data, is
Options A) 2x 3 + 7x 2 - 6x + 2 B)
2x 3 – 7x 2 + 6x - 2
C)
x 3 - 7x 2 – 6x2 + 1
D)
2x 3 - 7x 2 + 6x + 1
Your Answer ( Right Answer )
11 Two tools P and Q have signatures 5°-5°-6°-6°-8°-30°-0 and 5°-5°-7°-7°-8°-15°-0 (both ASA) respectively. They are used to turn components under the same machining conditions. If hp and hQ denote the peak-to-valley heights of surfaces produced by the tools P and Q, the ratio hp/hQ will be
Options A) B)
C) D)
Your Answer ( Right Answer )
12 A soldering operation was work-sampled over two days (16 hours) during which an employee soldered 108 joints. Actual working time was 90% of the total time and the performance rating was estimated to be 120 percent. If the contract provides allowance of 20 percent of the total time available, the standard time for the operation would be
Options A) 8min. B) 8.9 min.
C) 10 min D) 12 min.
Your Answer ( Not Answered )
Correct Answer D
13 A welding operation is time-studied during which an operator was pace-rated as 120%. The operator took, on an average, 8 minutes for producing the weld-joint. If a total of 10% allowances are allowed for this operation, the expected standard production rate of the weld-joint (in units per 8 hour day) is
Options A) 45 B) 50
C) 55 D) 60
Your Answer ( Not Answered )
Correct Answer A
14 In PERT analysis a critical activity has
Options A) maximum Float B) zero Float
C) maximum Cost D) minimum Cost
Your Answer ( Not Answered )
Correct Answer B
15 Through holes of 10 mm diameter are to be drilled in a steel plate of 20 mm thickness. Drill spindle speed is 300 rpm, feed 0.2 mm/rev and drill point angle is 120°. Assuming drill overtravel of 2 mm, the time for producing a hole will be
Options A) 4 Seconds B) 25 seconds
C) 100 seconds D) 110 seconds
Your Answer ( Right Answer )
16 Environment friendly refrigerant R134 a is used in the new generation domestic refrigerators. Its chemical formula is
Options A) CH C1 F 2 B) C 2 C1 3 F 3
C) C 2 C1 2 F 4 D) C 2 H 2 F 4
Your Answer ( Not Answered )
Correct Answer D
17 A standard machine tool and an automatic machine tool are being compared for the production of a component. Following data refers to the two machines.
Standard
Machine Tool
Automatic
Machine Tool
Setup time 30 min. 2 hours
Machining time per piece 22 min. 5min
Machine rate Rs. 200 per hour Rs. 800 per hour
The breakeven production batch size above which the automatic machine tool will be economical to use, will be
Options A) 4 B) 5
C) 24 D) 225
Your Answer ( Right Answer )
18 The mechanism of material removal in EDM process is
Options A) Melting and Evaporation B) Melting and Corrosion
C) Erosion and Cavitation D) Cavitation and Evaporation
Your Answer ( Not Answered )
Correct Answer A
19 From a pack of regular playing cards, two cards are drawn at random. What is the probability that both cards will be Kings, if the first card is NOT replaced?
Options A) 1
26
B) 1
52
C) 1
169
D) 1
221
Your Answer ( Not Answered )
Correct Answer D
20 The strength of a brazed joint
Options A) decreases with increase in gap between the two joining surfaces B) increases with increase in gap between the two joining surfaces
C) decreases up to certain gap between the two joining surfaces beyond which it increases D) increases up to certain gap between the two joining surfaces beyond which it decreases
Your Answer ( Not Answered )
Correct Answer D
|
|
|
|
|
|
|
|
|
|
|